-- ******************************************************************* -- CISCO-LWAPP-DOT11-CLIENT-MIB.my: Dot11 Wireless Clients MIB -- -- June 2006, Devesh Pujari, Srinath Candadai -- March 2011 Suja Thangaveluchamy -- -- Copyright (c) 2006, 2010-2012 by Cisco Systems Inc. -- All rights reserved. -- ******************************************************************* -- CISCO-LWAPP-DOT11-CLIENT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, Counter64, IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue, MacAddress, TimeInterval, DisplayString, TimeStamp, RowStatus FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI SnmpAdminString FROM SNMP-FRAMEWORK-MIB cLApDot11IfSlotId, cLApName, cLApLocation, cLApIfLoadChannelUtilization, cLApDot11RadioChannelNumber, cLAPGroupVlanName, cLApSubMode FROM CISCO-LWAPP-AP-MIB CLApIfType, CLDot11ClientStatus, CLClientPowerSaveMode, CcxServiceVersion FROM CISCO-LWAPP-TC-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB CiscoURLStringOrEmpty FROM CISCO-TC cLMobilityExtMCClientAnchorMCPrivateAddress, cLMobilityExtMCClientAnchorMCPrivateAddressType, cLMobilityExtMCClientAssociatedMAAddress, cLMobilityExtMCClientAssociatedMAAddressType, cLMobilityExtMCClientAssociatedMCAddress, cLMobilityExtMCClientAssociatedMCAddressType, cLMobilityExtMCClientAssociatedMCGroupId, cLMobilityExtMCClientAnchorMCGroupId FROM CISCO-LWAPP-MOBILITY-EXT-MIB VlanId FROM Q-BRIDGE-MIB; --******************************************************************** --* MODULE IDENTITY --******************************************************************** ciscoLwappDot11ClientMIB MODULE-IDENTITY LAST-UPDATED "201104290000Z" ORGANIZATION "Cisco Systems Inc." CONTACT-INFO " Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com" DESCRIPTION "This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is about the configuration and monitoring of 802.11 wireless clients in the network. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Basic Service Set ( BSS ) Coverage area of one access point is called a BSS. An access point (AP) acts as a master to control the clients within that BSS. Clear To Send (CTS) Refer to the description of RTS. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. MAC Service Data Units ( MSDU ) The MSDU is that unit of data received from the logical link control ( LLC ) sub-layer which lies above the medium access control ( MAC ) sub-layer in a protocol stack. Message Integrity Code ( MIC ) A value generated by a symmetric key cryptographic function. If the input data are changed, a new value cannot be correctly computed without knowledge of the symmetric key. Thus, the secret key protects the input data from undetectable alteration. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node, Mobile Station(Ms) and client are used interchangeably. Request To Send ( RTS ) A client wishing to send data initiates the process by sending a Request To Send (RTS) frame. The destination client replies with a Clear To Send (CTS) frame. Wireless local-area network ( WLAN ) A local-area network that uses high-frequency radio waves rather than wires to communicate between nodes. Service Set Identifier (SSID) A service set identifier is a name that identifies a particular 802.11 wireless LAN. A client device receives broadcast messages from all access points within range advertising their SSIDs. The client device can then either manually or automatically based on configuration select the network with which to associate. The SSID can be up to 32 characters long. Hybrid Remote Edge Access Point (HREAP) HREAP is a wireless solution for branch office and remote office deployments. It enables customers to configure and control access points in a branch or remote office from the corporate office through a wide area network (WAN) link without deploying a controller in each office. Workgroup Bridge ( WGB ) A WGB can provide a wireless infrastructure connection for a Ethernet-enabled devices. Devices that do not have a wireless client adapter in order to connect to the wireless network can be connected to a WGB through Ethernet port. KTS (Key Telephone System) Key Telephone System is an alternative to a private branch exchange (PBX) phone system. A KTS is equipped with several buttons that allow a caller to directly select outgoing lines or incoming calls, and use intercom and conference facilities. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol " REVISION "201104290000Z" DESCRIPTION "Added ciscoLwappDot11ClientMIBStatusGroupRev2, ciscoLwappDot11ClientMIBNotifsGroupRev2, and ciscoLwappDot11ClientMIBNotifControlGroup. Deprecated ciscoLwappDot11ClientMIBCompliance and added ciscoLwappDot11ClientMIBComplianceRev2" REVISION "200611210000Z" DESCRIPTION "Initial version of this MIB module. " ::= { ciscoMgmt 599 } ciscoLwappDot11ClientMIBNotifs OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIB 0 } ciscoLwappDot11ClientMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIB 1 } ciscoLwappDot11ClientMIBConform OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIB 2 } ciscoLwappDot11ClientCcxMIBObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIB 3 } cldcConfigObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBObjects 1 } cldcNotifObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBObjects 2 } cldcStatusObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBObjects 3 } cldcStatisticObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBObjects 4 } cldcCcxObjects OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientCcxMIBObjects 1 } --******************************************************************** -- Wireless Clients --******************************************************************** cldcClientTable OBJECT-TYPE SYNTAX SEQUENCE OF CldcClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the 802.11 wireless clients that are associated with the APs that have joined this controller. An entry is created automatically by the controller when the client gets associated to the AP. An existing entry gets deleted when the association gets dropped. Each client added to this table is uniquely identified by the client's MAC address." ::= { cldcStatusObjects 1 } cldcClientEntry OBJECT-TYPE SYNTAX CldcClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An entry is identified the client's MAC address." INDEX { cldcClientMacAddress } ::= { cldcClientTable 1 } CldcClientEntry ::= SEQUENCE { cldcClientMacAddress MacAddress, cldcClientStatus CLDot11ClientStatus, cldcClientWlanProfileName SnmpAdminString, cldcClientWgbStatus INTEGER, cldcClientWgbMacAddress MacAddress, cldcClientProtocol INTEGER, cldcAssociationMode INTEGER, cldcApMacAddress MacAddress, cldcIfType CLApIfType, cldcClientIPAddress IpAddress, cldcClientNacState INTEGER, cldcClientQuarantineVLAN VlanId, cldcClientAccessVLAN VlanId, cldcClientLoginTime TimeStamp, cldcClientUpTime TimeInterval, cldcClientPowerSaveMode CLClientPowerSaveMode, cldcClientCurrentTxRateSet OCTET STRING, cldcClientDataRateSet OCTET STRING, cldcClientHreapApAuth INTEGER, cldcClient80211uCapable TruthValue, cldcClientPostureState TruthValue, cldcClientAclName SnmpAdminString, cldcClientAclApplied INTEGER, cldcClientRedirectUrl CiscoURLStringOrEmpty, cldcClientAaaOverrideAclName SnmpAdminString, cldcClientAaaOverrideAclApplied INTEGER, cldcClientUsername SnmpAdminString, cldcClientSSID SnmpAdminString, cldcClientSecurityTagId Unsigned32, cldcClientTypeKTS TruthValue, cldcClientIpv6AclName DisplayString, cldcClientIpv6AclApplied INTEGER, cldcClientDataSwitching INTEGER, cldcClientAuthentication INTEGER, cldcClientChannel Unsigned32, cldcClientAuthMode INTEGER, cldcClientReasonCode INTEGER, cldcClientSessionID SnmpAdminString, cldcClientApRoamMacAddress MacAddress, cldcClientMdnsProfile SnmpAdminString, cldcClientMdnsAdvCount Unsigned32, cldcClientPolicyName SnmpAdminString, cldcClientAAARole SnmpAdminString, cldcClientDeviceType SnmpAdminString, cldcUserAuthType INTEGER } cldcClientMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the MAC address of the client for this entry and uniquely identifies this entry. " ::= { cldcClientEntry 1 } cldcClientStatus OBJECT-TYPE SYNTAX CLDot11ClientStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The object that represents the current status of the client." ::= { cldcClientEntry 2 } cldcClientWlanProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the WLAN Profile name this 802.11 wireless client is connected to." ::= { cldcClientEntry 3 } cldcClientWgbStatus OBJECT-TYPE SYNTAX INTEGER { regClient(1), wgbClient(2), wgb(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The object that represents the work group bridging status of a DOT11 client. 'regClient' - The client is a wireless client 'wgbClient' - The client is connected via a WGB 'wgb' - The client is the WGB itself." ::= { cldcClientEntry 4 } cldcClientWgbMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the MAC address of the WGB this 802.11 wireless client to which it is connected. This returns a non-zero value when the cldcClientWgbStatus is wgbClient." ::= { cldcClientEntry 5 } cldcClientProtocol OBJECT-TYPE SYNTAX INTEGER { dot11a (1), dot11b(2), dot11g(3), unknown(4), mobile(5), dot11n24(6), dot11n5(7), ethernet(8), dot3(9), dot11ac5(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The 802.11 protocol type of the client. 'dot11a' - The client is using 802.11a standard to connect to the access point (AP) 'dot11b' - The client is using 802.11b standard to connect to the access point (AP) 'dot11g' - The client is using 802.11g standard to connect to the access point (AP) 'unknown' - The client protocol is unknown 'mobile' - The client using mobile wireless to connect to the access point (AP). 'dot11n24' - The client is using 802.11n standard with 2.4 GHz frequency to connect to the access point (AP) 'dot11n5' - The client is using 802.11n standard with 5 GHz frequency to connect to the access point (AP). 'ethernet' - The client is using ethernet standard to connect to the access point (AP). 'dot3' - The client is using dot3 standard to connect to the access point (AP). 'dot11ac5' - The client is using 802.11ac standard with 5 GHz frequency to connect to the access point (AP)." ::= { cldcClientEntry 6 } cldcAssociationMode OBJECT-TYPE SYNTAX INTEGER { unknown(1), wep(2), wpa(3), wpa2(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The association mode for which the key decrypt error occurred." ::= { cldcClientEntry 7 } cldcApMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the radio MAC address of a LWAPP AP. " ::= { cldcClientEntry 8 } cldcIfType OBJECT-TYPE SYNTAX CLApIfType MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the wireless interface type." ::= { cldcClientEntry 9 } cldcClientIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " This object specified client's IP address. " ::= { cldcClientEntry 10 } cldcClientNacState OBJECT-TYPE SYNTAX INTEGER { quarantine(1), access(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the client's network admission control state. 'quarantine' - The client goes through posture analysis and the client traffic is sent by controller in quarantine vlan. 'access' - The client traffic is sent by controller in access vlan. The client should have completed posture analysis. Posture Analysis is a state change where the client applies the configured policies to validate access to the network." ::= { cldcClientEntry 11 } cldcClientQuarantineVLAN OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the quarantine VLAN for client. The quarantine VLAN only allows limited access to the network." ::= { cldcClientEntry 12 } cldcClientAccessVLAN OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the access VLAN for client. The access VLAN allows unlimited access to the network." ::= { cldcClientEntry 13 } cldcClientLoginTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the value of sysUpTime when the client logged in." ::= { cldcClientEntry 14 } cldcClientUpTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the duration for which the client has been associated with this device." ::= { cldcClientEntry 15 } cldcClientPowerSaveMode OBJECT-TYPE SYNTAX CLClientPowerSaveMode MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the power management mode of the client." ::= { cldcClientEntry 16 } cldcClientCurrentTxRateSet OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) UNITS "Mbit/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current data rate at which the client transmits and receives data. The data rate field is a 16-bit unsigned value expressing the data rate of the packets received by the client." REFERENCE "RFC 5416" ::= { cldcClientEntry 17 } cldcClientDataRateSet OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..126)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the set of data rates at which the client may transmit data. Each client can support up to 126 rates. Each octet contains an integer value representing one of these 126 rates ranging from 1 Mb/s to 63.5 Mb/s. One of the supported rates will be chosen by the access point for trasnmission with the client." REFERENCE "RFC 5416" ::= { cldcClientEntry 18 } cldcClientHreapApAuth OBJECT-TYPE SYNTAX INTEGER { true(1), false(2), notApplicable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the client is locally authenticated or authenticated by the controller. Local authentication is done only if the Access Point connected to the client is of hreap mode. A value of 'true' indicates that the client is locally authenticated. A value of 'false' indicates that the client is authenticated by the controller. A value of 'notApplicable' indicates that client is not connected to a HREAP." ::= { cldcClientEntry 19 } cldcClient80211uCapable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the client supports 802.11u feature. The 802.11u standard allows devices such as laptop computers or cellular phones to join a wireless LAN widely used in the home, office and some commercial establishments. A value of 'true' indicates that the client supports the 802.11u feature. A value of 'false' indicates that the client does not support the 802.11u feature." REFERENCE "IEEE 802.11u" ::= { cldcClientEntry 20 } cldcClientPostureState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Posture state of the client. Posture Analysis is a state change where the client applies the configured policies to validate access to the network. A value of 'true' indicates that the client supports the Posture feature. A value of 'false' indicates that the client does not support the Posture feature." ::= { cldcClientEntry 21 } cldcClientAclName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ACL Name for the client." ::= { cldcClientEntry 22 } cldcClientAclApplied OBJECT-TYPE SYNTAX INTEGER { true(1), false(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ACL applied status for the client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'notAvailable' indicates that applied status is not available" ::= { cldcClientEntry 23} cldcClientRedirectUrl OBJECT-TYPE SYNTAX CiscoURLStringOrEmpty MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the AAA override redirect URL for a client with cldcClientPostureState enabled. The object has a valid value when the WLAN, with which the client has associated requires Conditional or Splash-Page Web Redirection. This object is otherwise not applicable, and contains a zero-length string." ::= { cldcClientEntry 24 } cldcClientAaaOverrideAclName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the AAA Override ACL Name for the client if cldcClientPostureState is enabled on the wlan." ::= { cldcClientEntry 25 } cldcClientAaaOverrideAclApplied OBJECT-TYPE SYNTAX INTEGER { true(1), false(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the AAA Override ACL applied status for the client if cldcClientPostureState is enabled on the wlan. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'notAvailable' indicates that applied status is not available" ::= { cldcClientEntry 26} cldcClientUsername OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the username used by the client." ::= { cldcClientEntry 27 } cldcClientSSID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the SSID of the WLAN to which the client is associated." ::= { cldcClientEntry 28 } cldcClientSecurityTagId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the security group tag of the client. This parameter will have a non-zero value when the client is DOT1X authenticated." ::= { cldcClientEntry 29 } cldcClientTypeKTS OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the Client is NEC KTS Client or not. A value of 'true' indicates that the client follows NEC KTS SIP protocol. A value of 'false' indicates that the client does not follow NEC KTS SIP protocol." ::= { cldcClientEntry 30} cldcClientIpv6AclName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the ACL Name for the Ipv6 client." ::= { cldcClientEntry 31 } cldcClientIpv6AclApplied OBJECT-TYPE SYNTAX INTEGER { true(1), false(2), notAvailable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the ACL applied status for the IPv6 client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'NotAvailable' indicates that applied status is not avaliable" ::= { cldcClientEntry 32} cldcClientDataSwitching OBJECT-TYPE SYNTAX INTEGER { unknown(1), central(2), local(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies whether client is switching data locally or centrally." ::= { cldcClientEntry 33} cldcClientAuthentication OBJECT-TYPE SYNTAX INTEGER { unknown(1), central(2), local(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies whether client is authentiated locally or centrally." ::= { cldcClientEntry 34} cldcClientChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the access point's channel to which the client is associated." ::= { cldcClientEntry 35} cldcClientAuthMode OBJECT-TYPE SYNTAX INTEGER { none (0), psk (1), radius (2), cckm (3), wapipsk (4), wapicert (5), ftDot1x(6), ftPsk(7), pmfDot1x(8), pmfPsk(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the Authentication Mode of Client." ::= { cldcClientEntry 36} cldcClientReasonCode OBJECT-TYPE SYNTAX INTEGER { unspecified(1), previousAuthNotValid (2), deauthenticationLeaving (3), disassociationDueToInactivity (4), disassociationAPBusy (5), class2FrameFromNonAuthStation (6), class2FrameFromNonAssStation (7), disassociationStaHasLeft (8), staReqAssociationWithoutAuth (9), invalidInformationElement(40), groupCipherInvalid (41), unicastCipherInvalid (42), akmpInvalid (43), unsupportedRsnVersion (44), invalidRsnIeCapabilities(45), cipherSuiteRejected(46), missingReasonCode (99), maxAssociatedClientsReached(101), maxAssociatedClientsReachedOnRadio(105), maxAssociatedClientsReachedOnWlan(106), unSpecifiedQosFailure(200), qosPolicyMismatch(201), inSufficientBandwidth(202), inValidQosParams(203) } MAX-ACCESS read-only STATUS current DESCRIPTION "unspecified - Unspecified. previousAuthNotValid - Previous Authentication was not valid. deauthenticationLeaving - Leaving due to deauthentication. disassociationDueToInactivity - Disassociation due to Inactivity. disassociationAPBusy - Disassociation since AP was busy. class2FrameFromNonAuthStation - Class 2 frame from non authenticated station. class2FrameFromNonAssStation - Class 2 frame from non associated station. disassociationStaHasLeft - Station has left due to disassociation. staReqAssociationWithoutAuth - Station send association request without authentication. invalidInformationElement - Invalid information element. groupCipherInvalid - Invalid group Cipher. unicastCipherInvalid - Invalid unicast cipher. akmpInvalid - Invalid AKMP. unsupportedRsnVersion - Unsupported RSN version. invalidRsnIeCapabilities - Invalid RSN IE capabilities. cipherSuiteRejected - Cipher suite rejected. missingReasonCode - Reason code is missing. maxAssociatedClientsReached - Maximum allowed associated client number has reached. maxAssociatedClientsReachedOnRadio - Maximum allowed associated client number has reached on radio. maxAssociatedClientsReachedOnWlan - Maximum allowed associated client number has reached on wlan. unSpecifiedQosFailure - Unsupported QOS failure. qosPolicyMismatch - Mismatch on QOS policy. inSufficientBandwidth - Insufficient bandwidth. inValidQosParams - Invalid QOS parameters." ::= { cldcClientEntry 37 } cldcClientSessionID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the session to which the client is associated." ::= { cldcClientEntry 38} cldcClientApRoamMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the MAC address of the AP to which the client has roamed." ::= { cldcClientEntry 39 } cldcClientMdnsProfile OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the mDNS Profile name this 802.11 wireless client is mapped to. It could be mapped to the WLAN to which the client is connected to, or the interface/interface groups mapped to the WLAN." ::= { cldcClientEntry 40 } cldcClientMdnsAdvCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the number of mDNS advertisements received on the client." ::= { cldcClientEntry 41} cldcClientPolicyName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the local classification policy to which the client is associated." ::= { cldcClientEntry 42} cldcClientAAARole OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the role string of the client that is used as match criterion for local policy profiling. This string is returned during authentication. " ::= { cldcClientEntry 43} cldcClientDeviceType OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the device type of the client. This is identified once the profiling operation is completed." ::= { cldcClientEntry 44} cldcUserAuthType OBJECT-TYPE SYNTAX INTEGER { open(1), wepPsk(2), portal(3), simPeap(4), other(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the Authentication Type of User." ::= { cldcClientEntry 45} cldcClientByIpTable OBJECT-TYPE SYNTAX SEQUENCE OF CldcClientByIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the 802.11 wireless clients that are associated with the APs that have joined this controller and are indexed by cldcClientByIpAddressType and cldcClientByIpAddress. An entry is created automatically by the controller when the client gets associated to the AP. An existing entry gets deleted when the association gets dropped." ::= { cldcStatusObjects 2 } cldcClientByIpEntry OBJECT-TYPE SYNTAX CldcClientByIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An entry is identified by the client's IP address." INDEX { cldcClientMacAddress, cldcClientByIpAddressType, cldcClientByIpAddress } ::= { cldcClientByIpTable 1 } CldcClientByIpEntry ::= SEQUENCE { cldcClientByIpAddressType InetAddressType, cldcClientByIpAddress InetAddress, cldcClientByIpAddressDiscoverType INTEGER, cldcClientByIpAddressLastSeen TimeStamp } cldcClientByIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the type of the Client's address made available through cldcClientByIpAddress." ::= { cldcClientByIpEntry 2 } cldcClientByIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the inet address of the Client" ::= { cldcClientByIpEntry 3 } cldcClientByIpAddressDiscoverType OBJECT-TYPE SYNTAX INTEGER { invalid(1), ndp(2), dhcp(3), packet(4), local(5), static(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the discovery type of the Client's address invalid(1) = unknown ndp(2) = Address learnt by neighbor discovery protocol dhcp(3) = Address learnt via DHCP packet(4) = Address learnt by data packet addressing learning local(5) = Address applied to local interface static(6) = Address assigned statically " ::= { cldcClientByIpEntry 4 } cldcClientByIpAddressLastSeen OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates timestamp of the time when an address was last seen in REACHABLE state" ::= { cldcClientByIpEntry 5 } --******************************************************************** --* Sleeping Client Details --******************************************************************** cldcSleepingClientTable OBJECT-TYPE SYNTAX SEQUENCE OF CldcSleepingClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This table represents the information about Sleeping clients" ::= { cldcStatusObjects 3 } cldcSleepingClientEntry OBJECT-TYPE SYNTAX CldcSleepingClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the information about sleeping clients." INDEX { cldcSleepingClientMacAddress } ::= { cldcSleepingClientTable 1 } CldcSleepingClientEntry ::= SEQUENCE { cldcSleepingClientMacAddress MacAddress, cldcSleepingClientSsid OCTET STRING, cldcSleepingClientUserName SnmpAdminString, cldcSleepingClientRemainingTime TimeInterval, cldcSleepingClientRowStatus RowStatus } cldcSleepingClientMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the MAC address of the sleeping client and uniquely identifies the entry." ::= { cldcSleepingClientEntry 1 } cldcSleepingClientSsid OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the SSID of the WLAN to which the sleeping client is associated." ::= { cldcSleepingClientEntry 2 } cldcSleepingClientUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the username used by the sleeping client." ::= { cldcSleepingClientEntry 3 } cldcSleepingClientRemainingTime OBJECT-TYPE SYNTAX TimeInterval UNITS "Hours" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the remaining session time for the sleeping client." ::= { cldcSleepingClientEntry 4 } cldcSleepingClientRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This is the status column for this row and used to delete specific instances of row in the table." ::= { cldcSleepingClientEntry 5 } --******************************************************************** --* Wireless client statistics --******************************************************************** cldcClientStatisticTable OBJECT-TYPE SYNTAX SEQUENCE OF CldcClientStatisticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table lists statistics and status of the 802.11 wireless clients associated with the access points attached to the controller." ::= { cldcStatisticObjects 1 } cldcClientStatisticEntry OBJECT-TYPE SYNTAX CldcClientStatisticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table provides traffic statistics of the associated client based upon its Mac address." INDEX { cldcClientMacAddress } ::= { cldcClientStatisticTable 1 } CldcClientStatisticEntry ::= SEQUENCE { cldcClientDataRetries Counter64, cldcClientRtsRetries Counter64, cldcClientDuplicatePackets Counter64, cldcClientDecryptFailures Counter64, cldcClientMicErrors Counter64, cldcClientMicMissingFrames Counter64, cldcClientRaPacketsDropped Counter64, cldcClientInterimUpdatesCount Counter64, cldcClientDataBytesReceived Counter64, cldcClientRealtimeBytesReceived Counter64, cldcClientRxDataBytesDropped Counter64, cldcClientRxRealtimeBytesDropped Counter64, cldcClientDataBytesSent Counter64, cldcClientRealtimeBytesSent Counter64, cldcClientTxDataBytesDropped Counter64, cldcClientTxRealtimeBytesDropped Counter64, cldcClientDataPacketsReceived Counter64, cldcClientRealtimePacketsReceived Counter64, cldcClientRxDataPacketsDropped Counter64, cldcClientRxRealtimePacketsDropped Counter64, cldcClientDataPacketsSent Counter64, cldcClientRealtimePacketsSent Counter64, cldcClientTxDataPacketsDropped Counter64, cldcClientTxRealtimePacketsDropped Counter64, cldcClientTxDataPackets Counter64, cldcClientTxDataBytes Counter64, cldcClientRxDataPackets Counter64, cldcClientRxDataBytes Counter64 } cldcClientDataRetries OBJECT-TYPE SYNTAX Counter64 UNITS "Retries" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of attempts made by the client before transmitting the MSDU successfully." ::= { cldcClientStatisticEntry 1 } cldcClientRtsRetries OBJECT-TYPE SYNTAX Counter64 UNITS "Retries" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of times the client has attempted to send RTS packets before receiving CTS packets." ::= { cldcClientStatisticEntry 2 } cldcClientDuplicatePackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of times a duplicate packet is received for the client." ::= { cldcClientStatisticEntry 3 } cldcClientDecryptFailures OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of packets received from the client that failed to decrypt properly." ::= { cldcClientStatisticEntry 4 } cldcClientMicErrors OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of MIC errors experienced by the client." ::= { cldcClientStatisticEntry 5 } cldcClientMicMissingFrames OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of missing MIC packets for the client." ::= { cldcClientStatisticEntry 6 } cldcClientRaPacketsDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of RA Packets dropped for this client." ::= { cldcClientStatisticEntry 7 } cldcClientInterimUpdatesCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of interim updates count sent for this client." ::= { cldcClientStatisticEntry 8 } cldcClientDataBytesReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number data bytes received for this mobile station" ::= { cldcClientStatisticEntry 9 } cldcClientRealtimeBytesReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number realtime bytes received for this mobile station" ::= { cldcClientStatisticEntry 10 } cldcClientRxDataBytesDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Rx data bytes dropped for this mobile station" ::= { cldcClientStatisticEntry 11 } cldcClientRxRealtimeBytesDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Rx realtime bytes dropped for this mobile station" ::= { cldcClientStatisticEntry 12 } cldcClientDataBytesSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number data bytes Sent for this mobile station" ::= { cldcClientStatisticEntry 13 } cldcClientRealtimeBytesSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number realtime bytes Sent for this mobile station" ::= { cldcClientStatisticEntry 14 } cldcClientTxDataBytesDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Tx data bytes dropped for this mobile station" ::= { cldcClientStatisticEntry 15 } cldcClientTxRealtimeBytesDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Tx realtime bytes dropped for this mobile station" ::= { cldcClientStatisticEntry 16 } cldcClientDataPacketsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number data Packets received for this mobile station" ::= { cldcClientStatisticEntry 17 } cldcClientRealtimePacketsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number realtime Packets received for this mobile station" ::= { cldcClientStatisticEntry 18 } cldcClientRxDataPacketsDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Rx data Packets dropped for this mobile station" ::= { cldcClientStatisticEntry 19 } cldcClientRxRealtimePacketsDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Rx realtime Packets dropped for this mobile station" ::= { cldcClientStatisticEntry 20 } cldcClientDataPacketsSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number data Packets Sent for this mobile station" ::= { cldcClientStatisticEntry 21 } cldcClientRealtimePacketsSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number realtime Packets Sent for this mobile station" ::= { cldcClientStatisticEntry 22 } cldcClientTxDataPacketsDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Tx data Packets dropped for this mobile station" ::= { cldcClientStatisticEntry 23 } cldcClientTxRealtimePacketsDropped OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number Tx realtime Packets dropped for this mobile station" ::= { cldcClientStatisticEntry 24 } cldcClientTxDataPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of data packets sent by this mobile station" ::= { cldcClientStatisticEntry 25 } cldcClientTxDataBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of data bytes sent by this mobile station" ::= { cldcClientStatisticEntry 26 } cldcClientRxDataPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of data packets sent for this mobile station" ::= { cldcClientStatisticEntry 27 } cldcClientRxDataBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of data bytes sent for this mobile station" ::= { cldcClientStatisticEntry 28 } --******************************************************************** --* Client Ccx Services Version Table --******************************************************************** cldccCcxVersionInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CldccCcxVersionInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the detail of the CCX version supported by the clients. This is used to identify the services supported by a CCX v6 client." ::= { cldcCcxObjects 1 } cldccCcxVersionInfoEntry OBJECT-TYPE SYNTAX CldccCcxVersionInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the table for each entry identified by the client mac address." INDEX { cldcClientMacAddress } ::= { cldccCcxVersionInfoTable 1 } CldccCcxVersionInfoEntry ::= SEQUENCE { cldccCcxFoundationServiceVersion CcxServiceVersion, cldccCcxLocationServiceVersion CcxServiceVersion, cldccCcxVoiceServiceVersion CcxServiceVersion, cldccCcxManagementServiceVersion CcxServiceVersion } cldccCcxFoundationServiceVersion OBJECT-TYPE SYNTAX CcxServiceVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This is the CCX version supported by the client for the service, foundation." ::= { cldccCcxVersionInfoEntry 1 } cldccCcxLocationServiceVersion OBJECT-TYPE SYNTAX CcxServiceVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This is the CCX version supported by the client for the service, location." ::= { cldccCcxVersionInfoEntry 2 } cldccCcxVoiceServiceVersion OBJECT-TYPE SYNTAX CcxServiceVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This is the CCX version supported by the client for the service, voice." ::= { cldccCcxVersionInfoEntry 3 } cldccCcxManagementServiceVersion OBJECT-TYPE SYNTAX CcxServiceVersion MAX-ACCESS read-only STATUS current DESCRIPTION "This is the CCX version supported by the client for the service, management." ::= { cldccCcxVersionInfoEntry 4 } --******************************************************************** --* NOTIFICATION Control objects --******************************************************************** cldcKeyDecryptErrorEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappDot11ClientKeyDecryptError notification. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientKeyDecryptError notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientKeyDecryptError notification." DEFVAL { true } ::= { cldcConfigObjects 1 } cldcAssocNacAlertEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappDot11ClientAssocNacAlert notification. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientAssocNacAlert notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientAssocNacAlert notification." ::= { cldcConfigObjects 2 } cldcDisassocNacAlertEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappDot11ClientDisassocNacAlert notification. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientDisassocNacAlert notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientDisassocNacAlert notification." ::= { cldcConfigObjects 3 } cldcMovedToRunStateEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappDot11ClientMovedToRunState notification. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientMovedToRunState notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientMovedToRunState notification." ::= { cldcConfigObjects 4 } ciscoLwappDot11ClientStaticIpFailTrapEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The object to control the generation of ciscoLwappDot11ClientStaticIpFailTrap notification. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientStaticIpFailTrap notification. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientStaticIpFailTrap notification." DEFVAL { true } ::= { cldcConfigObjects 5 } --******************************************************************** --* NOTIFICATIONS Objects --******************************************************************** cldcClientRSSI OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the average RSSI for the Mobile Station." ::= { cldcNotifObjects 1 } cldcClientSNR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object specifies the average SNR for the Mobile Station." ::= { cldcNotifObjects 2 } cldcDOT11ClientReasonCode OBJECT-TYPE SYNTAX INTEGER { unspecified(1), previousAuthNotValid (2), deauthenticationLeaving (3), disassociationDueToInactivity (4), disassociationAPBusy (5), class2FrameFromNonAuthStation (6), class2FrameFromNonAssStation (7), disassociationStaHasLeft (8), staReqAssociationWithoutAuth (9), invalidInformationElement(40), groupCipherInvalid (41), unicastCipherInvalid (42), akmpInvalid (43), unsupportedRsnVersion (44), invalidRsnIeCapabilities(45), cipherSuiteRejected(46), missingReasonCode (99), maxAssociatedClientsReached(101), maxAssociatedClientsReachedOnRadio(105), maxAssociatedClientsReachedOnWlan(106), unSpecifiedQosFailure(200), qosPolicyMismatch(201), inSufficientBandwidth(202), inValidQosParams(203) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "unspecified - Unspecified. previousAuthNotValid - Previous Authentication was not valid. deauthenticationLeaving - Leaving due to deauthentication. disassociationDueToInactivity - Disassociation due to Inactivity. disassociationAPBusy - Disassociation since AP was busy. class2FrameFromNonAuthStation - Class 2 frame from non authenticated station. class2FrameFromNonAssStation - Class 2 frame from non associated station. disassociationStaHasLeft - Station has left due to disassociation. staReqAssociationWithoutAuth - Station send association request without authentication. invalidInformationElement - Invalid information element. groupCipherInvalid - Invalid group Cipher. unicastCipherInvalid - Invalid unicast cipher. akmpInvalid - Invalid AKMP. unsupportedRsnVersion - Unsupported RSN version. invalidRsnIeCapabilities - Invalid RSN IE capabilities. cipherSuiteRejected - Cipher suite rejected. missingReasonCode - Reason code is missing. maxAssociatedClientsReached - Maximum allowed. associated client number has reached. maxAssociatedClientsReachedOnRadio - Maximum allowed associated client number has reached on radio. maxAssociatedClientsReachedOnWlan - Maximum allowed associated client number has reached on wlan. unSpecifiedQosFailure - Unsupported QOS failure. qosPolicyMismatch - Mismatch on QOS policy. inSufficientBandwidth - Insufficient bandwidth. inValidQosParams - Invalid QOS parameters." ::= { cldcNotifObjects 3 } cldcDOT11ClientTxDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the number of data packets sent by this mobile station" ::= { cldcNotifObjects 4 } cldcDOT11ClientTxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the number of data bytes sent by this mobile station" ::= { cldcNotifObjects 5 } cldcDOT11ClientRxDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the number of data packets sent for this mobile station" ::= { cldcNotifObjects 6 } cldcDOT11ClientRxDataBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the number of data bytes sent for this mobile station" ::= { cldcNotifObjects 7 } cldcClientVlanId OBJECT-TYPE SYNTAX Integer32 (0..4096) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Vlan ID of the Interface to which the client is associated." ::= { cldcNotifObjects 8 } cldcClientPolicyType OBJECT-TYPE SYNTAX INTEGER { dot1x(1), wpa1(2), wpa2(3), wpa2vff(4), notavailable(5), unknown(6), wapi(7) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Mode of the AP to which the Mobile Station is associated." ::= { cldcNotifObjects 9 } cldcClientEapType OBJECT-TYPE SYNTAX INTEGER { eapTls(1), ttls(2), peap(3), leap(4), speke(5), eapFast(6), notavailable(7), unknown(8) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Mode of the AP to which the Mobile Station is associated." ::= { cldcNotifObjects 10 } cldcClientAID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "AID for the mobile station" ::= { cldcNotifObjects 11 } cldcClientAuthenticationAlgorithm OBJECT-TYPE SYNTAX INTEGER { openSystem (1), sharedKey(2), unknown(3), openAndEap(129) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Authentication Algorithm of Mobile Station " ::= { cldcNotifObjects 12 } cldcClientWepState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "WEP State of Mobile Station" ::= { cldcNotifObjects 13 } cldcClientEncryptionCypher OBJECT-TYPE SYNTAX INTEGER { ccmpAes(1), tkipMic(2), wep40(3), wep104(4), wep128(5), none(6), notavailable(7), unknown(8), wapiSMS4(9) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Mode of the AP to which the Mobile Station is associated." ::= { cldcNotifObjects 14 } cldcClientPortNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through." ::= { cldcNotifObjects 15 } cldcClientAnchorAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates mobility Anchor address type." ::= { cldcNotifObjects 16 } cldcClientAnchorAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "If the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreign" ::= { cldcNotifObjects 17 } cldcClientEssIndex OBJECT-TYPE SYNTAX Unsigned32 (1..517) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Ess Index of the Wlan(SSID) that is being used by Mobile Station to connect to AP" ::= { cldcNotifObjects 18 } cldcClientCcxVersion OBJECT-TYPE SYNTAX INTEGER { notSupported(1), ccxv1(2), ccxv2(3), ccxv3(4), ccxv4(5), ccxv5(6), ccxv6(7) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Represents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP." DEFVAL { notSupported } ::= { cldcNotifObjects 19 } cldcClientE2eVersion OBJECT-TYPE SYNTAX INTEGER { notSupported(1), e2ev1(2), e2ev2(3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Represents the End-2-End Version the client is using for communication with the AP." ::= { cldcNotifObjects 20 } cldcClientInterface OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Name of the Interface of the mobile client to the switch." ::= { cldcNotifObjects 21 } cldcClientMobilityStatus OBJECT-TYPE SYNTAX INTEGER { unassociated(1), local(2), anchor(3), foreign(4), handoff(5), unknown(6), exportanchor(7), exportforeign(8) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Mobility Role of the Mobile Station." ::= { cldcNotifObjects 22 } cldcClientStatusCode OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Status Code of the Mobile Station" ::= { cldcNotifObjects 23 } cldcClientDeleteAction OBJECT-TYPE SYNTAX INTEGER { default(1), delete(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Action to Deauthenticate the Mobile Station. Set the State to delete." ::= { cldcNotifObjects 24 } cldcClientSecurityPolicyStatus OBJECT-TYPE SYNTAX INTEGER { completed(1), notcompleted(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "When this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be completed." ::= { cldcNotifObjects 25 } cldcClientTrapEventTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the inet address of the Client." ::= { cldcNotifObjects 26 } cldcClientPolicyManagerState OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents the current policy enforcement manager state of the client in controller." ::= { cldcNotifObjects 27 } cldcClientAssocTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the value of client association time" ::= { cldcNotifObjects 28 } cldcClientPmipDataValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents whether client has valid PMIP data." ::= { cldcNotifObjects 29 } cldcClientMobilityExtDataValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object represents new mobility status." ::= { cldcNotifObjects 30 } cldcClientPolicyErrors OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Number of Policy Errors for Mobile Station" ::= { cldcNotifObjects 31 } cldcClientSessionId OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the session to which the client is associated." ::= { cldcNotifObjects 32} cldcClientPmipNai OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the name of the profile, the client is associated to." ::= {cldcNotifObjects 33} cldcClientPmipState OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the state of the PMIP client: null: binding doesn't exist init: binding created, Retx timer running for PBU, binding not yet accepted from LMA, Tunnel/route is not yet setup active: binding accepted by LMA, refresh timer running, Tunnel/route setup complete. refreshPending: Refresh timer expired and Retx timer running. PBU refresh sent, PBA not yet received from LMA, (Tunnel/route is already setup). disconnectingSt: Dereg reply is expected. Retx timer is running, tunnel/route is still setup." ::= {cldcNotifObjects 34} cldcClientPmipInterface OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the interface to which the client is associated." ::= {cldcNotifObjects 35} cldcClientPmipHomeAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the type of the Client's Home address made available through cldcClientPmipHomeAddress." ::= {cldcNotifObjects 36} cldcClientPmipHomeAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the Home Address of the client." ::= {cldcNotifObjects 37} cldcClientPmipAtt OBJECT-TYPE SYNTAX INTEGER { reserved (1), logicalNetworkInterface(2), pointToPointInterface (3), ethernet (4), wirelessLan (5), wimax (6), threeGPPGERAN (7), threeGPPUTRAN (8), threeGPPETRAN (9), threeGPP2eHRPD (10), threeGPP2HRPD (11), threeGPP21xRTT (12), threeGPP2UMB (13) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the access technology type by which the client is currently attached." ::= {cldcNotifObjects 38} cldcClientPmipLocalLinkId OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the local link identifier of the client." ::= {cldcNotifObjects 39} cldcClientPmipLmaName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the LMA to which the client is connected." ::= {cldcNotifObjects 40} cldcClientPmipLifeTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the duration of the PMIP client association." ::= {cldcNotifObjects 41} cldcClientPmipDomainName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the domain to which the PMIP client is associated." ::= {cldcNotifObjects 42} cldcClientPmipUpKey OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the upstream key of the PMIP client." ::= {cldcNotifObjects 43} cldcClientPmipDownKey OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the downstream key of the PMIP client." ::= {cldcNotifObjects 44} --******************************************************************** --* NOTIFICATIONS --******************************************************************** ciscoLwappDot11ClientKeyDecryptError NOTIFICATION-TYPE OBJECTS { cldcAssociationMode, cldcClientMacAddress, cldcApMacAddress, cldcIfType, cLApName, cldcClientAuthMode } STATUS current DESCRIPTION "This notification is generated when a decrypt error occurs. The WEP WPA or WPA2 Key configured at the station may be wrong. cldcAssociationMode represents the association mode for which the key decrypt error occurred. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcIfType represents the wireless interface type of the client. cLApName represents the name of the AP to which the client is associated." ::= { ciscoLwappDot11ClientMIBNotifs 1 } ciscoLwappDot11ClientAssocNacAlert NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcClientWlanProfileName, cldcClientIPAddress, cldcApMacAddress, cldcClientQuarantineVLAN, cldcClientAccessVLAN, cldcClientAuthMode } STATUS current DESCRIPTION "This notification is generated when the client on NAC enabled SSIDs complete layer2 authentication . This is to inform about client's presence to the NAC appliance. cldcClientWlanProfileName represents the profile name of the WLAN, this 802.11 wireless client is connected to. cldcClientIPAddress represents the unique ipaddress of the client. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcClientQuarantineVLAN represents the quarantine VLAN for the client. cldcClientAccessVLAN represents the access VLAN for the client." ::= { ciscoLwappDot11ClientMIBNotifs 2 } ciscoLwappDot11ClientDisassocNacAlert NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcClientWlanProfileName, cldcClientIPAddress, cldcApMacAddress, cldcClientQuarantineVLAN, cldcClientAccessVLAN } STATUS current DESCRIPTION "This notification is generated when the controller removes the client entry on NAC enabled SSIDs. cldcClientWlanProfileName represents the profile name of the WLAN, this 802.11 wireless client is connected to. cldcClientIPAddress represents the unique ipaddress of the client. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcClientQuarantineVLAN represents the quarantine VLAN for the client. cldcClientAccessVLAN represents the access VLAN for the client. This is issued on NAC enabled ssids, whenever WLC removes client's entry." ::= { ciscoLwappDot11ClientMIBNotifs 3 } ciscoLwappDot11ClientMovedToRunState NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcClientIPAddress, cldcClientUsername, cldcClientSSID, cldcApMacAddress, cLApDot11IfSlotId, cLApName } STATUS current DESCRIPTION "This notification is generated when the client completes the PEM state and moves to the RUN state. cldcClientUsername represents the username used by the client. cldcClientIPAddress represents the unique ipaddress of the client. cldcClientSSID represents the SSID of the WLAN to which the client is associated. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cLApDot11IfSlotId represents the slotId of the AP to which the client is associated. cLApName represents the name of the AP to which the client is associated." ::= { ciscoLwappDot11ClientMIBNotifs 4 } ciscoLwappDot11ClientStaticIpFailTrap NOTIFICATION-TYPE OBJECTS { cldcClientMacAddress, cldcClientIPAddress } STATUS current DESCRIPTION "This is issued whenever the subnet defined for the Static IP of a Client is not found." ::= { ciscoLwappDot11ClientMIBNotifs 5 } ciscoLwappDot11ClientDisassocDataStatsTrap NOTIFICATION-TYPE OBJECTS { cLApName, cLApDot11IfSlotId, cldcClientByIpAddressType, cldcClientByIpAddress, cldcApMacAddress, cldcClientReasonCode, cldcClientUsername, cldcClientSSID, cldcClientSessionID, cldcClientTxDataPackets, cldcClientTxDataBytes, cldcClientRxDataPackets, cldcClientRxDataBytes } STATUS current DESCRIPTION "The disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation" ::= { ciscoLwappDot11ClientMIBNotifs 6 } ciscoLwappDot11ClientAssocDataStatsTrap NOTIFICATION-TYPE OBJECTS { cLApDot11IfSlotId, cldcClientByIpAddressType, cldcClientByIpAddress, cldcApMacAddress, cldcClientUsername, cldcClientApRoamMacAddress, cldcClientSSID, cldcClientTxDataPackets, cldcClientTxDataBytes, cldcClientRxDataPackets, cldcClientRxDataBytes } STATUS current DESCRIPTION "The associate notification shall be sent when the Station sends a association frame." ::= { ciscoLwappDot11ClientMIBNotifs 7 } ciscoLwappDot11ClientSessionTrap NOTIFICATION-TYPE OBJECTS { cLApDot11IfSlotId, cLApName, cldcClientByIpAddressType, cldcClientByIpAddress, cldcClientUsername, cldcClientSSID, cldcClientSessionID, cldcApMacAddress } STATUS current DESCRIPTION "Issued when the client completes the PEM state and moves to the RUN state." ::= { ciscoLwappDot11ClientMIBNotifs 8 } ciscoLwappDot11ClientAssocTrap NOTIFICATION-TYPE OBJECTS { cldcClientTrapEventTime, cldcClientMacAddress, cldcClientByIpAddressType, cldcClientByIpAddress, cldcClientPolicyType, cldcClientStatus, cldcClientAID, cldcApMacAddress, cLApDot11IfSlotId, cldcClientSSID, cldcClientAuthenticationAlgorithm, cldcClientEncryptionCypher, cldcClientPortNumber, cldcClientAnchorAddressType, cldcClientAnchorAddress, cldcClientEssIndex, cldcClientWlanProfileName, cldcClientWgbStatus, cldcClientWgbMacAddress, cldcClientCcxVersion, cldcClientE2eVersion, cldcClientInterface, cldcClient80211uCapable, cldcClientMobilityStatus, cldcClientRSSI, cldcClientSNR, cldcClientSecurityPolicyStatus, cldcClientLoginTime, cldcClientAssocTime, cldcClientCurrentTxRateSet, cldcClientDataRateSet, cldcClientHreapApAuth, cldccCcxFoundationServiceVersion, cldccCcxLocationServiceVersion, cldccCcxVoiceServiceVersion, cldccCcxManagementServiceVersion, cldcClientDataSwitching, cldcClientAuthentication, cLApDot11RadioChannelNumber, cLApIfLoadChannelUtilization, cLApLocation, cLAPGroupVlanName, cLApSubMode, cldcClientIPAddress, cldcClientSessionId, cldcClientVlanId, cldcClientProtocol, cldcClientEapType, cldcClientPolicyErrors, cldcClientDataRetries, cldcClientRtsRetries, cldcClientDataBytesSent, cldcClientDataBytesReceived, cldcClientDataPacketsSent, cldcClientDataPacketsReceived, cldcClientTxDataBytesDropped, cldcClientRxDataBytesDropped, cldcClientTxDataPacketsDropped, cldcClientRxDataPacketsDropped } STATUS current DESCRIPTION "The notification shall be sent when the Station associats to controller." ::= { ciscoLwappDot11ClientMIBNotifs 9 } ciscoLwappDot11ClientDeAuthenticatedTrap NOTIFICATION-TYPE OBJECTS { cldcClientTrapEventTime, cldcClientUpTime, cldcClientMacAddress, cldcClientByIpAddressType, cldcClientByIpAddress, cldcClientPostureState, cldcClientProtocol, cldcClientVlanId, cldcClientPolicyType, cldcClientEapType, cldcClientStatus, cldcClientAID, cldcApMacAddress, cLApDot11IfSlotId, cldcClientSSID, cldcClientAuthenticationAlgorithm, cldcClientWepState, cldcClientEncryptionCypher, cldcClientPortNumber, cldcClientAnchorAddressType, cldcClientAnchorAddress, cldcClientEssIndex, cldcClientWlanProfileName, cldcClientWgbStatus, cldcClientWgbMacAddress, cldcClientCcxVersion, cldcClientE2eVersion, cldcClientInterface, cldcClient80211uCapable, cldcClientMobilityStatus, cldcClientRSSI, cldcClientSNR, cldcClientDataRetries, cldcClientRtsRetries, cldcClientUsername, cldcDOT11ClientReasonCode, cldcClientStatusCode, cldcClientDeleteAction, cldcClientSecurityPolicyStatus, cldcClientNacState, cldcClientLoginTime, cldcClientAssocTime, cldcClientCurrentTxRateSet, cldcClientDataRateSet, cldcClientHreapApAuth, cldccCcxFoundationServiceVersion, cldccCcxLocationServiceVersion, cldccCcxVoiceServiceVersion, cldccCcxManagementServiceVersion, cldcClientDataSwitching, cldcClientAuthentication, cldcClientByIpAddressDiscoverType, cldcClientByIpAddressLastSeen, cldcClientPowerSaveMode, cLApDot11RadioChannelNumber, cLApIfLoadChannelUtilization, cLApLocation, cLAPGroupVlanName, cLApSubMode, cldcClientIPAddress, cldcClientPolicyErrors, cldcClientPolicyManagerState, cldcClientDataBytesSent, cldcClientDataBytesReceived, cldcClientDataPacketsSent, cldcClientDataPacketsReceived, cldcClientTxDataBytesDropped, cldcClientRxDataBytesDropped, cldcClientTxDataPacketsDropped, cldcClientRxDataPacketsDropped, cldcClientSessionId } STATUS current DESCRIPTION "The notification shall be sent when the Station gets de-authenticated." ::= { ciscoLwappDot11ClientMIBNotifs 10 } ciscoLwappDot11ClientMovedToRunStateNewTrap NOTIFICATION-TYPE OBJECTS { cldcClientTrapEventTime, cldcClientMacAddress, cldcClientByIpAddressType, cldcClientByIpAddress, cldcClientPostureState, cldcClientProtocol, cldcClientVlanId, cldcClientPolicyType, cldcClientEapType, cldcClientStatus, cldcClientAID, cldcApMacAddress, cLApDot11IfSlotId, cldcClientWlanProfileName, cldcClientAuthenticationAlgorithm, cldcClientWepState, cldcClientEncryptionCypher, cldcClientPortNumber, cldcClientAnchorAddressType, cldcClientAnchorAddress, cldcClientEssIndex, cldcClientWgbStatus, cldcClientWgbMacAddress, cldcClientCcxVersion, cldcClientE2eVersion, cldcClient80211uCapable, cldcClientMobilityStatus, cldcClientRSSI, cldcClientSNR, cldcClientDataRetries, cldcClientRtsRetries, cldcClientUsername, cldcClientStatusCode, cldcClientSecurityPolicyStatus, cldcClientNacState, cldcClientLoginTime, cldcClientDataRateSet, cldcClientHreapApAuth, cldccCcxFoundationServiceVersion, cldccCcxLocationServiceVersion, cldccCcxVoiceServiceVersion, cldccCcxManagementServiceVersion, cldcClientDataSwitching, cldcClientAuthentication, cldcClientByIpAddressDiscoverType, cldcClientByIpAddressLastSeen, cldcClientPowerSaveMode, cLApDot11RadioChannelNumber, cLApIfLoadChannelUtilization, cLApSubMode, cldcClientIPAddress, cldcClientPolicyManagerState, cldcClientPmipNai, cldcClientPmipState, cldcClientPmipInterface, cldcClientPmipHomeAddrType, cldcClientPmipHomeAddr, cldcClientPmipAtt, cldcClientPmipLocalLinkId, cldcClientPmipDomainName, cldcClientPmipLmaName, cldcClientPmipUpKey, cldcClientPmipDownKey, cldcClientPmipLifeTime, cLMobilityExtMCClientAnchorMCPrivateAddressType, cLMobilityExtMCClientAnchorMCPrivateAddress, cLMobilityExtMCClientAssociatedMAAddressType, cLMobilityExtMCClientAssociatedMAAddress, cLMobilityExtMCClientAssociatedMCAddressType, cLMobilityExtMCClientAssociatedMCAddress, cLMobilityExtMCClientAssociatedMCGroupId, cLMobilityExtMCClientAnchorMCGroupId, cldcClientPmipDataValid, cldcClientMobilityExtDataValid, cldcClientSessionId } STATUS current DESCRIPTION "The notification shall be sent when the Station moves to run or authenticated state." ::= { ciscoLwappDot11ClientMIBNotifs 11 } ciscoLwappDot11ClientMobilityTrap NOTIFICATION-TYPE OBJECTS { cldcClientTrapEventTime, cldcClientUpTime, cldcClientMacAddress, cldcClientByIpAddressType, cldcClientByIpAddress, cldcClientPostureState, cldcClientProtocol, cldcClientVlanId, cldcClientPolicyType, cldcClientEapType, cldcClientStatus, cldcClientAID, cldcApMacAddress, cLApDot11IfSlotId, cldcClientSSID, cldcClientAuthenticationAlgorithm, cldcClientWepState, cldcClientEncryptionCypher, cldcClientPortNumber, cldcClientAnchorAddressType, cldcClientAnchorAddress, cldcClientEssIndex, cldcClientWlanProfileName, cldcClientWgbStatus, cldcClientWgbMacAddress, cldcClientCcxVersion, cldcClientE2eVersion, cldcClientInterface, cldcClient80211uCapable, cldcClientMobilityStatus, cldcClientRSSI, cldcClientSNR, cldcClientDataRetries, cldcClientRtsRetries, cldcClientUsername, cldcDOT11ClientReasonCode, cldcClientStatusCode, cldcClientDeleteAction, cldcClientSecurityPolicyStatus, cldcClientNacState, cldcClientLoginTime, cldcClientAssocTime, cldcClientCurrentTxRateSet, cldcClientDataRateSet, cldcClientHreapApAuth, cldccCcxFoundationServiceVersion, cldccCcxLocationServiceVersion, cldccCcxVoiceServiceVersion, cldccCcxManagementServiceVersion, cldcClientDataSwitching, cldcClientAuthentication, cldcClientByIpAddressDiscoverType, cldcClientByIpAddressLastSeen, cldcClientPowerSaveMode, cLApDot11RadioChannelNumber, cLApIfLoadChannelUtilization, cLApLocation, cLAPGroupVlanName, cLApSubMode, cldcClientIPAddress, cldcClientPolicyErrors, cldcClientPolicyManagerState, cldcClientDataBytesSent, cldcClientDataBytesReceived, cldcClientDataPacketsSent, cldcClientDataPacketsReceived, cldcClientTxDataBytesDropped, cldcClientRxDataBytesDropped, cldcClientTxDataPacketsDropped, cldcClientRxDataPacketsDropped, cldcClientSessionId } STATUS current DESCRIPTION "The notification shall be sent when the Station gets roamed." ::= { ciscoLwappDot11ClientMIBNotifs 12 } --******************************************************************* --* Compliance statements --******************************************************************** ciscoLwappDot11ClientMIBCompliances OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBConform 1 } ciscoLwappDot11ClientMIBGroups OBJECT IDENTIFIER ::= { ciscoLwappDot11ClientMIBConform 2 } ciscoLwappDot11ClientMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the SNMP entities that implement this MIB. " MODULE MANDATORY-GROUPS { ciscoLwappDot11ClientMIBConfigGroup, ciscoLwappDot11ClientMIBNotifsGroup, ciscoLwappDot11ClientMIBStatusGroup } ::= { ciscoLwappDot11ClientMIBCompliances 1 } ciscoLwappDot11ClientMIBComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMP entities that implement this MIB." MODULE -- this module MANDATORY-GROUPS { ciscoLwappDot11ClientMIBConfigGroup, ciscoLwappDot11ClientMIBNotifsGroup, ciscoLwappDot11ClientMIBStatusGroup, ciscoLwappDot11ClientMIBStatusGroupRev2, ciscoLwappDot11ClientMIBNotifsGroupRev2, ciscoLwappDot11ClientMIBNotifControlGroup } ::= { ciscoLwappDot11ClientMIBCompliances 2 } --******************************************************************** --* Units of conformance --******************************************************************** ciscoLwappDot11ClientMIBConfigGroup OBJECT-GROUP OBJECTS { cldcKeyDecryptErrorEnabled } STATUS current DESCRIPTION "This collection of objects specifies the required configuration parameters for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 1 } ciscoLwappDot11ClientMIBNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappDot11ClientKeyDecryptError } STATUS current DESCRIPTION "This collection of objects specifies the notifications for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 2 } ciscoLwappDot11ClientMIBStatusGroup OBJECT-GROUP OBJECTS { cldcClientStatus, cldcClientWlanProfileName, cldcClientWgbStatus, cldcClientWgbMacAddress, cldcClientProtocol, cldcAssociationMode, cldcApMacAddress, cldcIfType, cldcClientIPAddress, cldcClientNacState, cldcClientQuarantineVLAN, cldcClientAccessVLAN, cldcClientAuthMode } STATUS current DESCRIPTION "This collection of objects specifies the required status parameters for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 3 } ciscoLwappDot11ClientMIBStatusGroupRev2 OBJECT-GROUP OBJECTS { cldcClientLoginTime, cldcClientUpTime, cldcClientPowerSaveMode, cldcClientCurrentTxRateSet, cldcClientDataRateSet, cldcClientHreapApAuth, cldcClient80211uCapable, cldcClientDataRetries, cldcClientRtsRetries, cldcClientDuplicatePackets, cldcClientDecryptFailures, cldcClientMicErrors, cldcClientMicMissingFrames, cldcClientIPAddress, cldcClientNacState, cldcClientQuarantineVLAN, cldcClientAccessVLAN, cldcClientPostureState, cldcClientAclName, cldcClientAclApplied, cldcClientRedirectUrl, cldcClientAaaOverrideAclName, cldcClientAaaOverrideAclApplied, cldcClientUsername, cldcClientSSID } STATUS current DESCRIPTION "This collection of objects specifies the required status parameters for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 4 } ciscoLwappDot11ClientMIBNotifsGroupRev2 NOTIFICATION-GROUP NOTIFICATIONS { ciscoLwappDot11ClientAssocNacAlert, ciscoLwappDot11ClientDisassocNacAlert, ciscoLwappDot11ClientMovedToRunState } STATUS current DESCRIPTION "This collection of objects represents the notifications for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 5 } ciscoLwappDot11ClientMIBNotifControlGroup OBJECT-GROUP OBJECTS { cldcAssocNacAlertEnabled, cldcDisassocNacAlertEnabled, cldcMovedToRunStateEnabled } STATUS current DESCRIPTION "This collection of objects represents the objects that control the notifications for the 802.11 wireless clients." ::= { ciscoLwappDot11ClientMIBGroups 6 } END